I watched the video "Dirt-Cheap Solar Generator Setup - What Can It Power?" by Alex Beale yesterday. In the video, the presenter purchases a cheap solar panel and power bank for a total of $250 and tests household devices to see what kind of wattage it can take.

Turns out the cheap device can power most household objects. I'm curious if it's possible to try a similar setup to meaningfully cover my electricity usage on a day-to-day basis. Unlike the creator of this video, I don't have a yard. I'm exploring whether a solar solution could work with my constraints.

I wanted to share this idea with Tildes and hear any ideas/feedback/experiences from people who have tried something similar.

My goal

• Investigate whether it's feasible to save money with this setup
• If so, find a setup that I can use to power some or all of my household devices off-grid
• Pay less in electricity costs
• Be able to rely on my power bank when the building's power goes out

My current situation

• I live in an apartment in an urban area in the US northeast (southeastern Pennsylvania).
• I do NOT have a balcony (sadly).
• I have two south-facing windows and four west-facing windows (two of which get a LOT of light, two of which get a decent amount but not as much). However, my south-facing windows don't get direct sunlight most of the day since there is a building in the way (just a bit in the late afternoon).
• The dimensions of the windowsills are about 16 inches in depth and about 55 inches in width. That's enough for a small or medium-sized solar panel, but not most panels designed for outdoor use.
• I can open the windows all the way and it would be physically possible, in theory, to hang something outside rather than keeping it on the windowsill (we'll get into this...)
• I pay for all my electricity. The heat/air is central and inaccessible, as are a couple of the overhead lights (there are only a couple), but everything else could theoretically be replaced with energy from a power bank, I think.
• I already have a power purchase agreement with a renewable energy supplier. All my energy is "green" in the sense that I'm making it slightly more economically feasible to produce green energy.
• In a less expensive month, the bill might come to around $75. In an expensive month, it might come to around $350. If I heated the unit as much as I would like, it would be higher.
  • I'm pretty sure most of my electricity use is the heat/AC.
  • I'm pretty sure most of the remainder is the washer and dryer dishwasher, followed by the washer and dryer.
  • I spend some amount heating my water otherwise (shower, sinks), but I can't address that with a solar panel.
  • I wouldn't mind saving money on the rest if that's all that's feasible.

My power needs (I think)

• I don't know much power my oven uses. It's electric, which the internet says averages around 2500 W.
• My dishwasher runs at 120 V and 18.7 A. That is... uh... 2244 W. Also a lot.
• My dryer says 120 V on the machine, and if I look up the model number, it seems to be at 15 amps. So that's 1800 watts.
• My washing machine, uses....... IDK how many watts. No information on this thing exists. But it uses a 120 V outlet. The internet says an average washing machine could use up to 1400 W (sounds high, but okay).
• My computer has a 520 W power supply, but I doubt it ever uses that much. It's old and mostly runs Solitaire. Maybe one day I will get a fancy new machine that does like 1000 W.
• My fridge uses 115 V at 4.5 A. Let's pretend that's 120 V and say 540 W.
• I can't tell how many watts my TV uses, but the internet says it could be up to 200 W.

I would want a bit of breathing room with the rated wattage so that the power bank doesn't explode.

No way I can run all these devices simultaneously off the power bank, but perhaps I could time them. Even partial coverage could be adequate if it makes financial sense.

Possible spatial configurations

I see a few possibilities here:

1. Stick a bunch of solar panels in the windowsills, propped up at a suitable angle.
2. Stick the panel directly in the window like an air conditioner. In this case I would want to use a two-sided panel, since there would be some ambient light coming from the inside. This would inevitably reduce my home's energy efficiency, which I would have to account for.
3. Weld some sort of counterweight to a mounting system that I can use outside the window to perch the panel at an ideal angle. This would also reduce my home's energy efficiency, but maybe by less since the gap could be minimized. It is also probably illegal. And dangerous.
4. Just fill my living room with solar panels. I will need to have a conversation about that. But it could be done.

I think #1 is the only one that is actually reasonable. #2 would cost me too much in heating bills to make any sense. I think #3 would get me evicted or sued by the city. And #4 is unreasonable considering that I like to use my house to live in.

My budget

I would maybe spend $500-1000 on this if the payback period was a few years. Not more than 5 because panels by then will be a lot more efficient.

I guess I could spend more than that if it makes sense. I have good credit and a high credit limit. I don't make that much money but I could save for a bit or carry a balance for a bit. I think I would draw a hard line around $3000.

The power doesn't go out here too often, so that isn't the main selling point, more of a nice-to-have.

My research

I'm just looking on Amazon. I know I could maybe get something a little cheaper elsewhere. I'm searching for "power bank with solar panel".

• 4000+ W range: OUPES Mega 5 for $3300+ with panels (I think?). That's a lot of money for something that might not even work. And I don't believe it would be $3300, most other models I'm seeing are closer to $5000.
• 2200 W range: Jackery Explorer 2000 for $2500 with the 2 panels. Maybe this could cover my energy-intensive appliances, one at a time. Still expensive. The solar panels will... maybe fit in the window with about 1/2 inch to spare? I could angle them slightly if needed?
• 1800 W range: (maybe) Anker SOLIX C1000 for $800 with 1 panel. It also says 2400 W so idk what it is really. Can't determine the width of the solar panel.
• 1000 W range: EF ECOFlow River 2 for $700 with 1 panel. I am also not sure how big the panel is.
• 600 W range: SinKeu Portable Power Station for $230 with 1 panel.
• 300 W range: Marbero Solar Generator for $230 with 1 panel.

I'm discovering that these companies never specify the dimensions of the solar panels because they assume no one would ever use them indoors. Probably for good reason. If they don't fit horizontally, I guess I could stand them up lengthwise.

I'm sure it would be possible to find a cheaper solar panel separate from the power bank. But as a ballpark, those are my initial numbers.

Math

Imagine I spend $2500 on the 2200 W Jackery model, with 2 panels. I could put them in the two bright west-facing windows. Let's just pretend they can get their maximum output and that charging time isn't an issue.

Let's say I use this every time I run my oven, dryer, washer, or dishwasher (not at the same time), and otherwise I connect it to my fridge and most other electronics. (I know I said my oven could be 2500 W, but I usually just use one burner, and I bet that's more like 1500 W.) Let's pretend the hassle of running all those cables has been solved somehow.

I really don't know exactly what my electricity breakdown is. If I have the heat/AC mostly off and am not in the unit a whole lot (e.g. traveling for some of the month), that's when I end up with a $75/mo bill. But if I'm out of the unit, that means I'm also not using my dryer/washer and other devices as much. I guess the fridge was still on. The $350 side of things is because it's hot and I'm running the AC more, and maybe slightly higher dryer usage for some laundry-related reason. So maybe I'll say the minimum I'm spending on non-heat/AC electricity per month is $50-100, and at most maybe something like $150.

So in this super optimistic scenario, the portion of my monthly electricity bill I suspect I'd be able to theoretically save would be $50-150. Let's just say $100. That means it would take 25 months to pay back if all goes well. Honestly that's not so bad.

If I instead bought the 1000 W ECOFlow setup for $700, I could cover all my non-intensive electrical uses. The main beneficiary would be the refrigerator, the computer, and maybe the television. I think the savings there would be like $25-50/mo at most, being pretty generous. If I say $35, that would be about a 20-month payoff. That's also pretty good, but if it'll take about the same amount of time to pay for itself, I'd rather get the higher-wattage one.

Numerous caveats:

• It's not always sunny in Philadelphia.
• The panels will not be at 100% efficiency because the window is cloaked in shadow half the day, and there is no way I get the angle perfect, and maybe the glass affects how much energy they can absorb or something (would it help? hurt?). This isn't inherently an issue, except...
• ...that the charging time for the power station might be long. Some of the reviews say 6 hours in maximum sunlight, so for my use-case there's no way it would be faster than 12 hours for a full charge, and probably more. I use my appliances kind of a lot. The fridge is always running, and either the washer, dryer, oven, or dishwasher are running a pretty good chunk of the time. I think that I could get by with this... but I probably wouldn't be able to use it as much as I'd like (there are often moments where more than one is running simultaneously), so...
• ...the payoff time wouldn't actually be 25 months. I suspect there are some factors I'm not thinking about that would reduce the realistic amount of energy I'd save here. Let's say it is half as effective in my setup as a normal person's, because the sun is half as visible or something, and the charging time is too slow to use often, or whatever. At a 50-month payoff (4 years), I would start to get skeptical. But not inherently opposed.
• I use my windowsill for other things that like sunlight, like plants. I would have to move the plants that really love the sun somewhere slightly dimmer. Is it worth it???????
• I also like to look out my window, and if I had a huge solar panel there (especially if I had to stand it up vertically for space reasons), that would be a bummer perhaps.
• Constantly charging and discharging this thing probably reduces its effective wattage output fast. I.D.K. by how much. But there might be a point where I can't use it for my high-wattage devices, which would largely defeat the purpose of buying an expensive model. Not clear to me what the timeline for that would be.
• I still can't figure out if the panels would actually fit in my windowsill.
• Since it wouldn't be able to run more than one energy-intensive device simultaneously, I'd have to be careful not to keep it plugged in to too much stuff at once. It would overall be a bit of a hassle to plug in the panels and the charger and everything. Maybe the panels could stay plugged in, but even so.
• Running extension cords all over the house and putting a giant solar panel in even just one or two of the windows would result in a catastrophic domestic state of affairs. I can just imagine the eye-popping that would happen if I set that up unilaterally.

Takeaway

There is almost definitely something I am not considering. My math is so napkin-based, so imaginary and so optimistic.

But even if the practical efficiency isn't great, I feel like this could maybe possibly actually work, and could save me a bit of money. I would just have to spend it all up front. I mean I don't have $2500 on hand. But I could scrounge up part of it and put the rest on credit. And it would make for living room conversation with guests?

Realistically this seems like an amusing but too-annoying to actually do sort of project. If you know anyone who's done something silly like this and had it work, let me know! I'd be curious what their experience was.

Hello good and clever people of Tildes, I need some advice.

With electricity the price it is, and my wife having a sizable workshop in the garden, I'm looking for ways to bring down the heating cost.

Her workshop is 5m x 4m x 2.2m, and the wood is 44cm thick. It's a chunky beast. She makes gifts and personalised items, so when she has the heatpresses and mug/tumbler press on the go, it gets toasty. If the sun comes out, also toasty. However, over night, it gets super chilled, almost to whatever temp is outside. To combat this I decided to use a Govee Electric Space Heater, 1500W with Thermostat, WiFi & Bluetooth. However, this barely does anything and the electric usage flies up.

What are good options here? The office is about 10 metres from my house. It's too far to extend the home central heating via plumbing, plus too much lagging. I don't want to spend a fortune, so any sensible options I'm willing to entertain. If we're talking a couple of thousand, it's off the menu.

Thanks for any help.

Dropping an edit with a link to the actual cabin: https://www.tigersheds.com/product/the-gamma-44mm-log-cabin/

It's not like a USA style log cabin, that's for sure!

Edit 2: Okay - wall insulation looks like the next thing to tackle before even thinking about heating it. Thanks folks.

Assume cleaning is done on a regular basis. My apartment has a subtle "scent" from, what I assume to be, the vinyl flooring wax. I'd like that to not be the smell visitors first experience.

I'm considering an air purifier/diffuser, but don't know if they're effective.

Hi, I need to re-terminate a couple of wires I do not wish to replace entirely. I'm thinking of just buying a cheap Klein crimper but is there a reason to buy something more expensive? If somebody with experience has any recommendations here, I'd appreciate them. Thanks.

Edit: thanks to everyone for their prompt replies! I will go with your consensus of no need for an expensive tool right now.

Hey, so there's been an ice buildup in our fridge creeping along the back. After a while it hit the front, and tadaaaa, it finally got bad enough the door didn't close fully... So most everything outside of one big pile of vegetables got defrosted overnight. (On the plus side, I walked into having a nice big pancake breakfast!) We threw out the meats and moved the veggies to our other freezer. This at least let me finally disassemble everything and see what's in there. It looks like this in there:

https://imgur.com/a/YnGB3Zz

When we noticed this was happening a few months ago I turned off the ice maker switch in the back and, but it still kept doing this. There's still a ton of ice in the top tray, and set the temp to the max. But the fridge is right up against the left wall there, making it difficult/impossible to get the trays here out with the door blocking it. Additionally the right side has a dishwasher immediately next to it, so a decent amount of heat goes up the back. Then ALSO I found that big chunk of ice frosted on a pipe, so I wonder if it split? I'm unfamiliar with fridge design, so I don't know exactly what would give me the right answer.

I'm wondering what to do. My thoughts are that I've finally got the bottom tray/shelf/bucket thing out, so I could hammer the shit out of it and at least clear the bottom up... Then if I could get the top tray out I could see if removing all the ice in the top would stop the creep. I'm guessing that's a big fat no. At that point, is it possible to remove the ice module that I actively do not want anyway to see if it fixes anything, or is it integral to the freezer design? And at that point... Should we just get another fridge? Are there fridges without this busto icemaker shit nowadays? Thanks!

So this is ultimately a very oddball situation. Some background:

I live in a rancher in southern NJ. Fully electrified home.

I had recently installed minisplits to replace some electric baseboard heaters, covering about 2/3 of my home. This was fortunate, as I believe my blower fan in my central AC unit blew out. The minisplits + 1 window unit have actually been cheaper to operate than the old AC unit, so now I have a vestiegal high-velocity central AC system in my attic.

Namely, this means a lot of unused flexible, insulated ductwork and some ferro-fluids in my attic that should probably be blocked off and drained, respectively.

I've been contemplating on how to possibly repurpose some of this stuff to fix one of the biggest blind spots in my home: ventilation and filtering

My one bathroom exhaust fan vents directly into the attic, which is a moisture hell that needs solved.

There's no other ductwork in my home, and pretty much the only time fresh air gets in the house is if we crack windows or open doors.

So the theory is:

I route the bathroom exhausts into the old air handler coils to help capture the moisture and drain it out, then have it mix with some outside air and recirculate it into the house again.

Alternatively, routing some of the air between the attic/crawlspace/attached garage for preconditioning outside air as as well.

Is this insanity, or a remotely plausible idea? I'm fairly handy, and since its sbeing made with vestigial bits in spare time labor cost is much less of an issue than parts.

It's hot here in Germany at the moment, and I've found a new hobby: experimenting with different ways to keep the flat cool. Unfortunately, right now I'm doing that mostly on gut feeling, and I'd like to add some data to the mix so I can pretend that this is Serious Research™.

Does anyone know of some good smart thermometers that I can use both inside and out, and that I can regularly take automatic readings off? My main criteria are roughly:

• Reasonably waterproof and battery-powered - I'd like to put at least one on my balcony which isn't covered, so I want to be confident that it survives out there.
• Relatively cheap - I want around 4-6 different thermometers spread around the inside and outside of the flat to see how the sun's position affects the temperature, and I don't want to spend more than around 100€ on this project in total.
• Scriptable - for the data collection, my plan is to be able to run a script on a spare Raspberry Pi to download all of the data and potentially send alerts when something changes or when it makes sense to start opening doors and windows to cool the flat down.
• Not too complicated - looking around, some thermometers seem to require smart hubs and online accounts and things. Ideally, I can avoid all that - I want something that I can connect to from my home network and download data from as I need.

Right now, I've found a few different smart temperature sensors that I can buy off-the-shelf, but these seem to be on the more complicated end of the spectrum, and require central hubs and uploading all the data to clouds and things like that. Ideally I can avoid that. Alternatively, I have some RPi Pico boards at home, so if I can buy some sensors that I can connect to those, I could get those set up more simply. But with the DIY route, I'm worried about weatherproofing, especially if the temperature sensor needs to remain fairly exposed for an accurate reading.

So: do you have any recommendations either for simple smart sensors that I can buy, or for sensors that I could easily stick to a Pico and leave outside for at least the rest of the summer months?

Update:
I found the issue!

Stupidly, I had listened to the advice of YouTubers and Amazon reviews. In my sand filter, I had used the woolen balls. Even though I had been performing the cycle and flush, dumping the water, the woolen balls were not clean, they were green and completely swamped in algae.

I took them out, rinsed, sat them in some diluted bleach and rinsed again. I cleaned the filter thoroughly. Upon putting it all back together, throwing in some shock and giving it a few hours, along with a 1/5 pool water dump and replace, it's looking clear again.

Thank you for all of the advice. I'll move to sand in the near future so the rinse and dump cycles actually work.

Original message:
I wasn't sure which group to shove this in, I went for home improvement as this needs serious improvement.

To be honest, with how green it is, maybe enviro would have been even better.

I have an above ground 5800l pool, which I put up during the summer for the kids. This year I decided to go with Bromine in a float. I'm using the standard slow disjsolve capsules from Everclear. I chose Bromine as one of the kids has quite sensitive skin. I started out with the winder float, 6 tabs slowly dissolving. I gave it a couple of days and realised I didn't have strips to test, so I ordered some.

In this time, with lots of abuse, a very warm season for England and probably half a metric ton of sun cream, the water was looking a bit cloudy. No biggy, the great Flow Clear 800Gal/h sand filter would be helping... It didn't seem to be. The water went from cloudy to slightly green at the bottom. The algae was arriving.

I dipped a stick: bromine didn't even register. Hmmm. I ordered a second float and some algaecide to attack the issue. Two days later, we have 12 tabs in two floats, enough algaecide to clear the Amazon river (I jest), and I leave it to clear. The following day, it's less cloudy, still green tinted and bromine still does not register on the sticks.

Over today's use, it's gotten worse. I've ordered chlorine tabs instead because the bromine is not working. It should have worked. Does anyone know where I went wrong?

Tomorrow, I'll dump half the water (over 2000l down the drain), change the tablets over to chlorine, throw in some more algaecide and let the pump keep on pumping. Hopefully, as it refills, I should get some nice clear water that doesn't have a pH of near 9.

Help me Tildes! My refrigerator is leaking and I live in an apartment so I need to get a new fridge ASAP so that I don't cause water damage to my downstairs neighbors! Does anyone have a brand recommendation? All I really care about for this is avoiding brands that are known to be shitty.

I also will use this as an opportunity to replace the absolutely horrible microwave that came with this apartment. While all fridges are basically identical to me, I am very opinionated about microwaves:

• There must be a 30 second button that either starts the cooking or adds 30s more to the existing cooking
• 1-6 must be quick-access "microwave for this many minutes" buttons, so that i can press 1 and then 30 to microwave for 90s or 4 and then 30 for 4:30, etc
• I would really like a decent popcorn button that has a microphone to determine when to stop
• Multiple power levels that are actually good at being lower power (I am fine with power level 50 meaning "be on for 50% of the time" etc, I think that works pretty well)
• idk if this even needs to be said in the year 2024 but a spinning tray
• auto-stop on door open so I can press just 1 thing
• If I press 'stop' or open the microwave after it stops it's "haha I'm done" beeping sequence, it STOPS BEEPING (my current microwave keeps beeping even if I press stop and/or open the door and I hate it so so so so much)

Edit: Thanks everyone! Based on recs here I bought a fridge without an ice machine and not LG, and it will be installed on Monday! I don't live in a rented unit, but usually I just say "apartment" rather than "condo" when I'm talking about neighbors.

I didn't go for freezer on the bottom cos those all seem to be drawers and I guess I do have an opinion about fridges, which is that I don't want the freezer to be a drawer, I feel like I'd get too cold pulling things out of it. So I got freezer-on-top, fridge-on-bottom.

There was 1 microwave with all the features I wanted plus the feature I didn't know I wanted where the numbers are arranged the same as a phone instead of [12345][678910] in 2 rows (why would you reinvent how to display numbers like this????) so I bought that one, and everything will be delivered on Monday!

As the title says. If you're in the UK at the moment then you will invariably have a slug fest issue. The weather has been perfect for them to go crazy breeding.

I'm posting this under home improvement, I need to remove these pests to improve my home. They're starting to climb the house to get to the moist areas of damp located in the far roof section, and I'm in a decent sized semi-detached.

We started with salt around the house regularly, that has helped. My veggie patch is under attack. I've tried the copper wire and tape - there are trails across it as they don't care. Yesterday, 8 beer traps arrived. I set them up, however I didn't have any beer and opted for cider and white wine. In case you are trying this, slugs don't seem to be affected by a splash of Pinot Grigio, so don't bother. However, the cider traps had double digits in both. Tonight, the same 8 traps are out with cider and after a walk around the garden, I can see they like it a lot. However, there are still hundreds of the bastard things out there.

What are your proven methods to fend the mollusks off? Trap or pellet? Do you hunt them down and melt them in a bucket? Help!

In December 2023, I had the AC replaced for the upstairs of our house. Installed was a "Bryant Preferred 2 Ton" 227TAN02400A and the corresponding Fan Coil FV4CNF002L00.

Two weeks ago, when the heat came (I'm in NE Florida), I noticed that our upstairs was not able to keep up. We keep it set to 73 both up and downstairs and the upstairs unit was just continually running from 11AM-7PM and never getting below 76-77.

A tech came out and let me know that, based on the pressures he was seeing, the expansion valve and coil needed to be replaced. It was under warranty, so I said sure, go for it. The install was scheduled for Monday, a week ago.

That tech showed up last Monday and replaced both parts. When he left, he said that we should be good to go and everything was looking great. Last week was a milder week for temperatures (mid to high eighties), but I did notice the humidity was still quite high in the upstairs (in the 70's and low 80's).

Things still didn't seem right by the end of last week, so I called again and they scheduled someone to come out today.

When the guy showed up today, he checked the pressures and said I was on the low side of the manufacturer's specs. He topped it off a bit and brought me to the high side of the manufacturer's specs.

Of bigger concern he said that my drain pan was cracked. He said this had been identified by the very first tech and the part had been on order since then. He said they installed the coil and valve to get things cooling better even though they didn't have the drain pan in yet.

Today was the first I heard anything about the drain pan. Anyway, they are trying to get that as soon as possible and will have to install it when it comes in.

So, now that the background is done, here's my question. Would this cracked drain pan cause my cooling issues? Right now (4PM) it is 97 outside. My downstairs unit has no problem getting me to 73 and 50% humidity (and shutting off). The upstairs unit is running non-stop and is at 76 (set to 73) and 83% humidity.

I understand that the crack in drain pan is making it "all wet" inside the air handler. I understand that can cause the humidity to be high, but would that also be the cause for cooling issues?

Hi all,

I am in the middle of taking bids with my local HVAC companies and am looking for someone to nudge me in one direction or the other. For background, I bought my house in western Michigan, right off the lake Michigan coast near Grand Rapids, last Fall. My home inspection made it clear the AC would need work and I haven't started to feel the need for it until recently. I called an HVAC company out and when they said the unit was 25+ years old, I just told them to forget about even fixing it because it would be at least 10% of the cost of a new unit and still way less efficient.

So.

My natural gas furnace is also ~20 years old and the first HVAC guy said that if it broke down, it likely wouldn't pass a safety inspection. They said something about how the coils being dirty or positioned someway or something, I can't really recall 100% what the issue would be but the gist that I got was that when it breaks down, whether it be 1 year, 2 years, or 5 years, it won't be worth fixing or it will be unfixable. A new AC would be ~$6500 and a new furnace would be ~$7000.

So I started up the conversation towards installing a heat pump unit in instead of a standard AC unit. My initial thinking is that when the furnace goes, I have the back up ready to go instead. Now a heat pump unit is going to cost me around $2000 more. I don't think my plan will be to ever install a replacement furnace. Depending on what the solar assessment says, evaluating both ground mounted and roof mounted solar, will tell me how worth it is to go that route and have discounted or free heating and cooling.

Where the calculus gets tricky for me is there is the Inflation Reduction Act which will give me a $2000 tax credit for a heat pump. But that will come with buying a more expensive, and efficient unit, and I believe I will also have to completely get rid of the furnace I currently have since the total home system has to meet the efficiency standard. In addition, last month I replaced my fuse box with a 200 amp panel and if I meet the requirements to get the $2000 tax credit, I would also get $600 tax credit for the panel since I can tie them together.

All in all, I am looking at getting a more efficient unit for roughly the same price as the less efficient unit but without the natural gas furnace as either main heating, or back up heating. My hesitation is that natural gas is so cheap that it doesn't make sense financially to go heat pump only unless I have renewable energy to pair with it. But maybe I am just overthinking it? And maybe I have gotten something wrong in my calculations?

Any advice or clarifications would be greatly appreciated. I have one more quote coming this Thursday and I hope to make a decision by Friday to get the work started

New house owner here, a couple of weird plumbing things I'm noticing and not sure how big of a concern they are. All of these are very sporadic.

Possibly relevant things to note, I live in the US, we do not have a basement, do have a crawlspace, are connected to the town sewer lines, have lived in the house for about 2 weeks and it was vacant for a month prior to us moving in (with occasional visits and contractors.)

1. A couple of times, but only a couple, the bathroom sinks have made a sound when flushing the toilet. Maybe once this happened with the kitchen sink but I couldn't be sure. Not sure if this is something I should be trouble shooting or I'm overthinking it.

2. We've had occasional sewer gas odors. I've run water down the second bathroom's drains just in case it was due to those being unused, but I can't tell if that fixed it because it's inconsistent. Anything else I can/should do?

3. The main suite shower is a circular rain style shower head. Occasionally, hours or even a day after using it, it'll just run water, the way you'd expect it to drain out of the shower head after turning off the shower. The internet suggested this could be just something where the water is held in the shower head until air/water pressure shifts and it can escape. It's also possible that this needs a vinegar bath to clean up some hard water scaling. Am I on the right track?

4. One of my toilets keeps running/not running when the float gets stuck. I've fixed that before, though the last time I did it, it was a rubber float on a stick and this is some plastic contraption. (I am discovering home repair makes me feel like a 72 year old grumpy old man. ) Pretty sure I can clean it and see if that fixes it, adjust the screw on it, and replace it if needed. But any tips there besides a YouTube video or two?

Never owned a house before so any advice is worthwhile.

Not sure if this is a "home improvement" topic, but I didn't see anywhere else relevant this would fit so I am going to drop it here.

I've lived in the same place for around 12 years now. Before I moved in, the place was owned by one other person for around 10 years. The place is probably ~20 years old. I have two toilets in the house. About 5 years after I moved in, the flushing mechanisms on one of the toilets stopped working and I inspected it and it looked like the bobber/float switch was busted to the point where when it got to max height, the water flow wouldn't shut off.

I pulled up a couple articles on the internet and it seemed like the parts were pretty straight forward to replace. So I went to Lowes, got the replacement parts needed and a few hours later, toilet was fixed. No big deal. About a year later the other toilet started acting up in the same manner so I just did the same thing. Both toilets had the original parts in them. They were all metal parts. The replacement parts were a brand called "FluidMaster" and I didn't really think much of it at the time. The replacement parts were almost entirely plastic.

So fast forward to today, and I have replaced the innards of the toilets on a fairly routine basis. It seems like every 18 months or so, I am having to replace the innards of the toilets because the float switch starts to fail. I came home from a day vacation on Saturday evening to find that one of the toilets was running and for god knows how long. I open the lid and sure enough, bobber is at the top, but the float switch hadn't disabled the water flow so the toilet just keeps running. I turned off the water to it and made a note that I'll have to go back to Lowes and pick up more parts. This will be the fourth or fifth replacement I've had to do on it.

What's going on here? Why are these float switches in these kits breaking so frequently? Does anyone else have this problem? Am I just buying the wrong parts continuously? Is there a better set of parts that I can buy to correct this issue?

I'm right on the edge of buying a mini split for our shop space and I'm having a bout of indecisiveness.

To preface, we are located in south/central Texas. The shop is a standalone structure, is fairly well insulated but has a 2-car garage door and a single-pane window, so it isn't ideal. It's 625sqft with 9 foot ceilings. We have various tools that will be in use but nothing that creates excessive heat.

We are quite limited in funds so I'm not going with an HVAC company, nor am I going with a mr cool or other diy friendly unit due to cost. I'm capable to do the install myself, I'm not overly concerned about that.

I was originally looking at the 18k (1.5ton) senville leto. I ran various calculators and they all suggested this size would be enough up to 1000sqft or so. However, since I have 9 ft ceilings and I live in a hot climate and I have the big door and crappy window, the calculations pushed my 625sqft up to around 900 or so equivalent sqft in some cases and in others as high as 1200.

Due to my circumstances, I think I've convinced myself to move up to the 24k unit instead. I don't think it's too over provisioned for my specific scenario but I would like to hear your thoughts on how off the mark I am here.

Apart from size, there's also the question of efficiency. The other model I was looking at is the Aura by senville, and the difference is a higher seer2 rating and energy star certification.

Now, doing rough math, the difference in efficiency would be paid off by the savings of the more efficient unit in something like 8 or 9 years based on projected usage and my energy costs. I'm a pessimistic person and don't expect this unit to last 8-10 years. This is a cheap way to get the space comfortable to work in so that my side business can progress, and I would think if it's still going in that amount of time, I'll be able to afford a nicer unit by then.

However, after saying all that, I do notice that the capabilities of the Aura unit are greater. It is advertised to work in -20f weather while the leto works in as low as 5f.

Now, being in Texas, my primary concern is cooling, not heating, but no where can I find if the Aura system is more capable in hotter weather like it is in colder weather. This is slightly concerning because it seems most people use these primarily as heat sources and secondarily as cooling sources, and my situation is reversed.

Does anyone have any input as to whether the higher efficiency system will make a noticable difference in cooling performance when it's 110f outside?

Thanks for weathering my wall of text.

My backyard has become a muddy mess and it's creating some downstream effects, such as me spending WAY too much time vacuuming and mopping (3 dogs), and not being able to do anything meaningful in the backyard. Here are some details:

• I'm right on the edge of USDA zones 9a and 9b -- the map shows that my house is specifically in 9a, but one block south of me is 9b
• The grass in the backyard was mostly St. Augustine when I bought the house. For a number of reasons (some really harsh winters and summers, three dogs trampling the grass, etc.), the St. Augustine is entirely gone
• Last fall, as a stop-gap, I put down some weed killer to control the weeds and seeded the entire backyard with winter rye. It grew amazingly well and I had a lush, verdant backyard for one season.
• This spring, my plan was to grow bermuda grass. My thinking was that it would be able to withstand the summers but could also handle the dog traffic a bit better. So, I did some pre-emergent, scalped the winter rye, raked up most of the detritus, got the ground really wet and muddy, and laid down some bermuda seed + fertilizer
• Now, almost a month later, I haven't seen a single bit of growth. The pre-emergent has done a pretty good job of keeping the weeds out and some winter rye is still growing here and there, but other than that, it's just... mud.

So, what are my options, especially this late in the season? Should I just throw in the towel and sod it with St. Augustine again? Did I do something wrong with the bermuda? Do I need to make it through a muddy summer and reconsider my options going into the fall?

I'm in the process of moving apartments, and I'm realizing I don't have an elegant solution to all of the tech gadgets/accessories/junk my hoarding tendencies refuse to let go of.

By electronic accessories I mean all the cables, flash drives, SD cards, dongles, headphones, power bricks, etc. that have I've gathered over the years. There are some larger items like musical instrument cables, wireless speakers, an computer mouse, even an old PS3 I don't really know what to do with. While most don't get used frequently, there have definitely been times where one of these items comes in clutch.

I'm not opposed to getting dedicated furniture like an under-desk cabinet, although I would want to make sure the space is used efficiently, and that it can be sturdy enough to be multipurpose (e.g. my work office cabinets have a cushion that can be used for sitting on top of). I'm in NYC so space is a premium and there's a low likelihood that I'll have extra space in existing drawers/closets, so I'd prefer a standalone solution.

Hoping there might be some clever solutions/suggestions Tilerinos find handy, even if it's accepting that a Marie Kondo-style purge of unused electronics is necessary.

Hi, everyone. I'm on the hunt for opinions. I live in a colder climate in North America with no access to natural gas. Most heat their homes with propane or oil. Mine uses a very old 30+ year old oil boiler. I've started to see more pellet boilers, but I'm a bit uncertain about them at the moment. I don't like burning fossil fuels to heat my home, but electric isn't really an option out here and it's hard to argue with the "tried and true" cast iron boiler with the BTU per gallon oil offers. On the other hand, my local government is practically throwing money and/or attractive financing at people to switch.

I'm curious if anyone out there has made the switch to some kind of pellet-fed heating system from a fossil fuel system. If so, I'd love to hear what you think of them, be it good or bad.

I've always considered myself a rather clean and tidy person (and get comments from others to that effect), but realized I was never formally taught on best practices for cleaning. There are probably things I tend to overlook, things that may not be visible (best practices for cleaning pipes for example). There is likely a lot of "traditional" knowledge on cleaning I don't know.

I am curious if anyone here has some sort of "ultimate guide for spring cleaning" around the house to get everything to a nice deep clean, and some sort of routine on what someone should do every week/month/whatever in order to upkeep this cleanliness over the course of the year.

Not looking for some extreme clean freaks guide but I am genuinely curious as to what I may have missed and overlook as I was never really "taught" how to clean.

My wooden privacy fence was blown over in a storm (Houston, TX), any recommendations for the best way to rebuild?

Currently thinking of Shadowbox, fence hanger brackets, three rails, with a rot/kick board.

So I'm looking to get out of apartment living in the next couple of years, so I browse housing listings semi-frequently just to get an idea of what's out there and what I can expect cost wise.

My boss made an offhand comment about buying a lot and getting a prefab installed on it, so I started looking into it, but I came back with a lot of questions.

1. Home builders seem to have preset floor plans. Every time I try and find a prefab house, all I can find are blueprints for purchase. Do you find a plan you like and then find someone to build it?

2. Home builders I find all build giant houses. I always see comments online about how "Builders can't build affordable homes because of red tape," but I don't understand how that means they can only build 5B/3Ba houses. I cannot find anyone that has preset plans for a 2B house.

3. How much about getting a lot "ready" would be up to me vs a builder? Is that gonna depend on the builder and what they offer? Is that all done out of pocket, or would that be included in the construction loan?

For reference, I'm in Atlanta, though I imagine a lot of these answers will be "It depends on the builder."

I posted previously about looking for a house for my disabled partner and myself and after several stressful months we're closing on April 30th!

So, now what? I'm working on home insurance quotes, I have the money arranged for closing. We're in the "these issues need addressed" phase of the contract process (there are no smoke detectors in this house wtf) and the home inspection raised no dealbreakers. No radon or termites.

So what don't I know about? What new homeowner things do I need to be thinking about now? We plan to move in the latter half of May. Accessibility suggestions are also useful, we're going to have to add a small ramp inside (one step), move a cabinet in the kitchen and replace carpet in the master bedroom.

Thanks for all the advice last time, please give me more of it?

This is one of those bizarre examples where I think a simple Google would solve the mystery, but I've tried dozens of searches like "halogen track lights with LEDs in center" and NO product comes up with it. Does anyone know what these are?? My guess is that it has to do with one of the lights being out, but why so many LEDs then?

Hey folks - I've been wanting to go whole hog on automating my home, I read through this smart home automation - tips and tricks thread started by @Merry and had a lot of useful information.

Some of the things I took away from it:

• Home assistant is pretty great (if you don't mind tinkering)
• Getting something that will boot back up after a power failure is great
• Use smart plugs / switches vs bulbs
• Maintain it's usefulness if there is an internet outage

Like I mentioned I'd really like for this to be privacy focused and mostly self contained. Sure I'd love to be able to control stuff from my phone while I'm home and also recognize that I'm home or away.

I just am a bit smooth brained when it comes to even seeing "would something like this work with the wiring / circuity that I have in my home already?"

If there are any good guides to follow or really specific advice / steps I could follow to begin this process I'd really appreciate it.

I’m looking for advice about what sort of portable room cooling devices to look at and what pitfalls to avoid. Some context:

Over the past few years I’ve noticed that I do pretty badly in the heat, especially at night. I live in Zürich, the concept of air conditioning has not yet arrived in this place. The prevailing wisdom for how to survive summer is to just make sure your house doesn’t get too warm in the first place, but my apartment is pretty badly insulated and during the worst weeks it doesn’t cool down that much at night either, so it’s been pretty bad the last few years. I’ve mostly just avoided being in my room whenever possible, but I do have to sleep somehow.

The obvious solution to me is to buy some sort of air conditioning device, a topic I know basically nothing about. My flatmate has one for his room, of the “dangle a tube out of the window” kind, which seems to do an okay job, but it is extremely loud and quite bulky - neither of those are dealbreakers per se, but I’d happily pay a bit more money if that gets me something quieter. In addition, our windows are not sliding windows but ones that open like a door, so any device that requires me to poke something out of the window would probably need a solution for this as well. Any sort of permanent modification to the house such as putting a hole through the wall or the window glass are not allowed.

So my questions are: What types of coolers should I look into, what types are best avoided? Any specific brand or model recommendations would also be appreciated. I looked at one electronics vendor’s website and found a huge range in prices from below 100 to over 1000; I don’t have a specific budget in mind per se, but unless it makes a big difference (e.g. in noise levels) I would rather stay below 500 dollars.

Came home today and found wet clothes in the dryer. Which was weird because earlier, I had found the same load in there wet and just thought I had forgotten to start the dryer. Low and behold, when I stood and watched it, about ten seconds after starting it, it started beeping and gave out an F01 error code.

While googling it, it seemed that the code meant the relay electronics board had failed and needed to be replaced. I thought, I can probably do that, but the board seemed to be more than $150, which is more than the callout fee on our home warranty ($125). But what we most needed was a working dryer!

While looking for the exact price and a source to order the board, I found this video describing a simple fix for a blown solder connection. I unplugged the washer, opened it up, and the board was blown in the exact same spot as in the video. I soldered a jumper in, put it back together, and lo and behold, the dryer runs!

I have an undergraduate degree in electrical engineering, even though it hasn't been my day job in a long time. So I could at least evaluate the plausibility of the fix, and I had the tools and know-how to do the soldering. So definitely not a fix for everyone.

Money is tight right now, so fixing the dryer for $0 (and in half an hour no less) was big for us. Sometimes you need a win, and today was a day I really needed one!

What fixes around the house are you most proud of, saved you some money, or kept a piece of equipment out of the landfill?

We bought our house over eight years ago and it came with a number of appliances. Within the first year, both the refrigerator and the dishwasher crapped out on us. We replaced them with new Frigidaire and Whirlpool models respectively, but I definitely haven't been satisfied with them. Now my washer and dryer are acting up and I'm not sure how much longer they've got.

When our fridge first started giving us issues, we had someone come out to try to fix the existing one. He basically told us that it would be around $400 to replace the failing motherboard on it — and given how simple that fridge was, it was essentially the price of a replacement. So you can't fix anything—you just throw it into a landfill and buy a new one.

The principle of "you get what you pay for" doesn't seem to apply, either. I don't need a fridge that has a 20-inch OLED screen for connecting to a Samsung account. Paying more just seems to get you more features that are likely to cause problems down the road.

Before we bought our replacement dishwasher, I got a subscription to Consumer Reports. The one we got was one of their recommendations. But it's just… not a good dishwasher. Little parts of it keep failing (e.g., the top rack's glassware holder-spine-thingies). And it's leaking, too!

So, to bring it back around to the subject title, how do you even find reliable appliances? Does anyone even make reliable appliances? It seems like there has been a race to the bottom among all of the appliance manufacturers (not that this is a unique to appliances, as this Vox piece explains). Long-term reliability doesn't move units off the showroom floor, so it doesn't get prioritized. (Plus there's the whole economic disincentive for "durable goods" to actually be durable.) And with model numbers changing annually, there's no good way to keep track of which models have proven reliability.

Howdy all,

TL;DR - Installed new cabinets, picked up new butcher block countertops to match existing. Stained it - using the Minwax stain and planned on using Watco Butcher Block finish to finish it. I am concerned about food safety and health. Note I am not using these as actual cutting boards. Just countertops. Would using the Watco finish be safe/sufficient for sealing the stain?

So to give a little context, my wife and I moved into our home close to 5 years ago. The person who flipped our house put in standard big box birch butcher block countertops. We like them! They stained them a nice dark color and we have not thought much about them. From what they mentioned, they "finished" the counters with the Watco Butcher Block finish. Occasionally the areas near the sink get grey and dry from water and could use a clean/restoration. Of which I have been using Howard butcher block conditioner and I think it does a great job of giving the wood some life.

Now I finally got around to installing some more cabinets, and I picked up another countertop. Obviously wanting it to match, I just used the same Minwax stain that the flipper used. I had planned on sanding all of the old countertops re-applying the stain and then coating in some urethane-like topcoat in hopes of helping stop the discoloration and make the counter more durable.

This lead me down a rabbit hole of a bunch of people online basically yelling about putting anything other than butcher block finish or mineral oil on butcher block countertops and how its not food safe/toxic. So naturally this kind of freaked me out. Is the stain on the current counters harmful? Do I need to sand everything and then reapply with just a food safe option? Can I just sand and add a poly topcoat? Or am I fine to just have the stain on it and use the Watco butcher block finish? AM I POISONING MYSELF?!

I would like to add we do not use these countertops as actual cutting boards. We always use a "real" cutting board.

Really I am just looking for some advice or a sanity check to make sure I'm not harming ourselves. Hoping this could also help someone else learn without having to do it the hard way.

Thanks all so much for any info anyone is willing to provide.

So our freezer is dying. Our fridge is over 20 years old and has served us well, but it's time to move on. Given the reputation of modern appliances, the proliferation of smart appliances, and the current class-action lawsuit against LG and Kenmore over faulty compressors leading to fridges dying after just five years, I figured I'd ask for some recommendations on good brands.

For specifics, we don't need or want any fancy features beyond an ice maker. We'd prefer it to not have any smart features, just a good old simple fridge/freezer that can be expected to function fine for years (again, we've had the current one for 20 years). My mom says she'd prefer a fridge with a bottom freezer compartment, but I don't think that's a deal-breaker (our current one is a side-by-side) so long as it's a good model.

I'm currently working on decluttering, and coming up with processes to stop clutter from building up in the future.

Even after getting rid of a bunch of junk, I'll be left with a ton of stuff that historically has just "floated around" my living space (cables, adapters, small tools, stationary, batteries, etc...).

I'd ideally want a bunch of appropriately sized containers that I can organize stuff into. I'd love for each box to be some tesselation of a standard volume, so that I can arrange and stack those containers neatly in a drawer or on a desk.

If you happen to work with 3D printing, this may sound a lot like Gridfinity, a modular open-source grid storage system. And I agree! Gridfinity's goals completely meet and shoot past what I'm looking for. But I currently have no interest in investing the money or time into buying a 3D printer and making prints. And there doesn't appear to be an obvious commercial version outside of "random" folks on Etsy.

I also considered getting a Drawer Grid like you'd see in a Maker Space. I might end up getting this if I can't find a better option, though I'd prefer a storage solution I can stuff in a drawer.

I was curious if:

• Anyone had any product recommendations that might fit the bill
• Anyone had any thoughts on the organizational endeavor itself, and if there are any ways I could be going about this better.

Hey all,

Bought a house 2 years ago, and have had a handful of issues where I had to call someone out to take a look. Whether its plumbing/HVAC/whatever, sometimes they are clearly things I couldn't do myself, but other times, it feels like something I could probably do if I put aside the time.

Most recently, our sump failed resulting in some flooding and we had to get it replaced, which ended up costing $700 USD. I know pumps only cost around $300 and generally understand what work needs to go into replacing it, but was worried I may miss something crucial, especially when replacing the piping and screw the whole thing up. On the flip side, I've had a lot issues with our furnace, so the last time an issue came up, I spent an hour on Youtube and just figured it out myself.

Sometimes it just feels silly spending a bunch of money on labor, when its something you could spend an afternoon doing yourself. It just feels hard to gauge when its worth investing the time to figure it out myself or not. I also never know what to do in the situation when the person who took the time to come out gives me a price, it feels like your essentially trapped at that point.

Anyone with more home ownership experience have any advice?

I received a quote from a local contractor to do some home remodeling. Some of the numbers make sense, but some seem quite high. Like, I can't believe it costs $3k in labor to install an electric fireplace insert, or an island hood. Anybody have any insight they're willing to share on this quote?

Remodel estimate

1. Planning and asbestos test $1,190.00
2. Move range outlet $1,514.00
3. Island hood $4,498.00
4. Electric fireplace insert $4,133.00
5. Main bathroom $36,552.00
6. Hall bathroom toilet and fan with humidistat $3,579.00
7. Concrete landings outside the front and back doors, front siding flashing $2,899.00
8. Re-pipe plumbing $14,993.00
9. Bedroom window glass replacement $749.00
   Total $70,107.00

Description
Plans will be refined. Drywall will be tested for asbestos content.
Dust will be contained and floors will be protected.
The range outlet will be moved.
An island range hood will be installed. The placeholder hood in the estimate is a Zephyr Brisas.
An electric fireplace insert will be installed. The placeholder fireplace in the estimate is a
Dimplex 500001756.
The main bathroom will be remodeled. The shower will be replaced with a pre-formed shower
pan and Corian walls, and two shower valves and shower heads will be installed. A sliding
shower door will be installed. The floor will be tiled. A new vanity cabinet, countertop, sink, and
faucet will be installed. A new toilet will be installed. The vanity electrical outlets will be
lowered, a larger lower mirror will be installed, a new vanity light will be installed. A ventilation
fan and light will be installed with a humidistat/condensation sensor. Drywall will be patched.
New baseboard trim will be installed. The bathroom will be painted.
The hall bathroom toilet will be replaced. A ventilation fan with a humidistat will be installed.
Concrete landings will be poured outside the front door and outside the back sliding door. The
front door landing will be about 5-1/2’x4’ with a curved corner. The back landing will be about
3-1/2’x3’.
The plumbing in the house will be replaced. Drywall holes from installation will be patched and
painted.
Window glass will be replaced in the bedroom with the broken window pane.
Everything will be cleaned up.
All labor and materials are included.

Thank you!

I know for basic living for one single person and no pets, a bathroom, and kitchen+living room+bedroom are the bare essentials. So basically a studio.

What I'm looking for is some opinions on what separated rooms are needed/wanted for a house, and also how needed/wanted are they? I'd say the bathroom and "studio" room would rank as #1 and #2, unless you plan on having the "studio" area separate. In that case, these are ranked as:
Bathroom -1
Kitchen - 2
Bedroom - 3
Living room - 4

Maybe add in closets here and there, and a laundry room?

Bthrm closet - 5
Laundry - 6
Bdr closet - 7
Pantry - 8
Lvgrm closet - 9

But I know nothing of what rooms are necessary (or lesser known possible rooms/areas) for living, or even how big they should be. I know in my state, NC, the bare minimum is 720 sq ft, so shooting for slightly over that would be ideal for me. I don't want to have a huge house to clean, and I love cozy, small spaces. If I want to see some larger space, I'll look out a window or go outside.

So what would be your numbered list for priority rooms in a house?

Hey all. I have a room that's currently lit (during the night) by two light fixtures attached to the same wall and on the same switch. Each fixture has two LED lights with a 2700K or 2800K color temperature (don't remember exactly), 230lm brightness, 3.9W power consumption, for presumably a theoretical total of 920lm and 15.6W. These bulbs are angled some 45 degrees forward aimed at the (white) ceiling in order to reflect diffuse light for the rest of the room.

I'm going to add two tall bookcases to that wall which are going to cover where the lights currently are, so I need to figure out another solution for lighting. I don't want to damage the ceiling. Currently, my idea is to extend the wiring from the walls up behind the bookcases and place lights at the top of the bookcases, similarly angled forward so they reflect off the ceiling closer to the middle of the room.

But I'm not finding appropriate fixtures, devices or anything else that I can place on a horizontal surface in order to angle a directed diffuse light forward. The closest I have right now would be something like these outdoor waterproof floodlights.

They have a number of problems, though, chief of all the temperature being 3000K (that's the lowest available; you can get them a lot colder). For some reason, no one seems to be making 2700K/2800K versions of these. I'm afraid if I buy these, the light in this room will be noticeably different from the rest of the house. They are also very bright at 1000lm each (these are the darkest available; they make them even brighter) for a total 2000lm, more than twice the current brightness. I'm afraid if I sit in a room lit by these, it will affect the quality of my sleep.

Does anyone have any ideas that might yield something closer to what I currently have, but which can be placed atop the bookcases and directed forward and up, as desired? It's also important that replacements don't require waiting for a 6 week cargo ship voyage from somewhere in China, that the power consumption isn't significantly higher, and that there won't be some huge monstrous device on the bookcase visible from the ground.

Sorry if this is a bit materialistic.

I think furniture reveals a lot about people, and the way that people organise their space is really interesting to me. For example I allocate a vast amount of space for bookshelves, whereas some people like to have big open spaces.

Personally my favourite furniture brand is probably Vitsoe. There's also often some fantastic furniture on EBay, or available at auction from offices (a really mad thing is that it's fairly common for office rental contracts to require the entire fitout to be ripped out and the office returned unfurnished – this often means everything including the ceiling panels and floorboards is throw out – even if the next tennant would happily accept the fitout) as people move out.

p.s. people who buy really expensive furniture which looks super ugly just so that they can flex their expensive furniture are the worst

I'm in the market for a set of dishes. The consensus is:

• Corelle - lightweight and solid
• Fiestaware - built to last

I'm not a fan of either unfortunately. Not because these brands are bad, but I'm looking for a particular look. Something akin to stoneware with a darker color. I also prefer heavier dishes. Unfortunately stoneware is known (or said) to chip easily. I'm not looking for something that will survive being dropped (I don't remember the last time I dropped a plate). This is the first selling point that gets brought up I've noticed.

What did you choose and what has been your experience? Has your stoneware chipped after washing & stacking?

EDIT
I forgot to provide more details about my situation to help with recommendations.

• I'm in the US
• No family/single, but plan to host for a small group on an occasion (~4 people)
• I'm starting from scratch and would like a set that works in all situations + everyday use. I'm willing to splurge (assuming it's quality and lasts).

Any advice on how to clean & control dust in the home?

I live in an apartment with no central HVAC, and i suppose certain life choices contribute to excess dust build up.. like

1. Air drying clothes-- All the fibers & dust don't get trapped in the dryer, they kind of stay on clothes until they dry and fall off in my apartment
2. windows are left open (depending on weather)
3. working on sewing projects

Not willing to change any of the above, so i might just have to deal with dusting all the time.

But dusting itself is difficult... Dusters that move dust off surfaces seem perpetually inefficient and can't capture 100%.
Wiping down surfaces is better but even microfiber cloths don't pick up everything either. Clumps up weirdly. And don't want to use a wet rag for dusting off books e.g.

Any suggestions are appreciated!

So here's my situation and what I'm trying to prepare for. My mom is currently sick (we think it's an infection), and last night she fell and threw up, scared me half to death. She says she's fine(ish) now, and we're waiting on test results. It got me thinking how she said I'll inherit her Siamese cat breeding business and it got me thinking a lot about it.

I'm wanting to divide what is currently a purely aesthetic room so the queens can have more room for their kittens who then won't get to hide under/in the couch (yes, inside the couch, because they tore holes in the fabric underneath it, apparently) whenever I try to show them to customers.

I want to divide my dining room from the entry way, where the front door leads into the living room, so the cats don't escape out the front door. Imagine a hallway (12 to 14 feet long) from the front door to the living room (and it's a double wide doorless doorway connecting it to the living room), but one wall of the hallway doesn't exist, and instead opens fully into the dining area. I haven't measured yet, but I'm estimating it's around 12 to 14 feet across, and 9 or 10 feet tall.

I'd like to use something budget friendly (ofc), like plexiglass, acrylic, resin, whatever. Something fully see through (or as see through as possible) so the customers can see them immediately. Proper glass will need a whole installation process and will add to the cost. Also, I'll want to add a door to this new "window wall" so the customers and I can walk in and out, and preferably have it be a sliding door, since I think this is the option that will be the least likely to pinch a kitten.

My dad suggested a garage screen door, with magnetic closing, made of fiber glass mesh, but I can already tell the cats will eventually tear it up and make it look ratty, and also slip out from under it most likely.

We can't use normal room dividers because our cats can sometimes jump from the floor to the top of the fridge, and room dividers are too flimsy. Also I'm not sure how to fasten a door to them (maybe I could just open them, but idk).

I've also half-way crossed any meshes, cages, or fencing off my option list because it looks ratty imo. Btw when I say "ratty" I mean it will make me look like some backyard breeder or someone who doesn't care about her cats. I don't want my kittens to look like inmates lol. But cages/metal bars are a last resort, because I need something, as right now my mom has them set up in what I personally consider to be cages that are far too small to keep the mother cat in 24/7 for 2 to 4 weeks. The mother cat can just about lay down once you have to put the litterbox in. (It's the vertical one with the 3 tier platforms, with wheels and a bottom tray that you can find on amazon)

I've looked all over amazon, just window (lol) shopping/browsing for ideas on what I could use, and omg. Either inflation is horrible, or I'm severely out of touch with what a "budget" option for this project would be.

I've even gone so far as to consult ChatGPT, who was not really that helpful.

A list of things I've thought about already are:
-Garage screen doors (cats will eventually scratch through and slip under)
-Sliding barn doors (for the end of the entry way that leads into the living room, instead of dividing the dining room, but this would give the kittens and queens access to the front door when people go in and out)

• Those DIY metal grid panels people use to build storage furniture (ratty looking, and kind of expensive, but is my last resort as it seems to be the cheapest option I think)
• Ordering a proper glass window wall (this would have to be properly installed into the house, which would cost too much)
• Normal room dividers (too flimsy, too short, no door option)
• Chain link fence segments (definitely ratty looking)
• Decorative metal/PVC room divider modular panels that hang from the ceiling (I can't seem to find a version that has ample visibility without giant holes the kittens could slip through)
• Just building a bigger cage (more expensive than just building a wall out of the panels, and again, it's ratty looking)
• Using clear acrylic modular panels with holes in the corners, chained/tied together to hang from the ceiling (it's an option, but I'm not sure if it's the best in terms of aesthetics & cost, and idk how to attach a door that way)
• 3D printed prefab wall panels (not see through, and idk if/how I'd fit a door on it)
• Prefab floor to ceiling windows (expensive, heavy, needs proper installation I think)
• A clear, plastic tent piece, large enough for a patio (that would also look bad, since it's shiny and most likely will get scratched up)

I may be forgetting some options that I considered already, but I'm a complete novice at construction and home improvement, so I figured you guys probably know something I don't. I need a true barrier, that is preferably as clear as possible.

Even if you think your idea isn't all that good, suggest it anyway because I might be able to springboard off of it. This includes ideas relating to stuff I've thought of already.

Next week, I will be closing on my first ever home (hello Michigan tilderinos!). One of the projects I want to tackle and work on after I move in is setting up a smart home ecosystem that is sustainable long-term. I saw the open-source Home Assistant but I think I need to do more research on it and find compatible products. For now, my wishlist of projects are:

• Controllable lighting from my phone or computer
• Carbon Monoxide/Natural Gas detection
• Water leak and usage monitoring
• Thermostat

Are there any other use cases that you use home automation for? If you use Home Assistant (or used it in the past), what are some things I should consider? Any products that you bought in the past and regret now?

Hello... looking to hang a 100lbs heavy bag in my basement (with regular wood-stud walls). I've researched various options and have gone down all sorts of engineering rabbit holes, including pull-out strengths of various sized lag bolts, horizontal load maximums of different kinds of wood, etc. I've perused various marketplaces for various types of mounting solutions and such. The problem with standard DIY wall mounting is that it doesn't come off the wall far enough.

I'm wondering though -- and it seems simple enough of a solution -- why the following wouldn't work:

An 8-foot span of 2x6, turned "vertically" so that the top and bottom faces are the 2" edge, affixed 45 degrees to the studs. ASCII art not-withstanding, it's just an isosceles triangle, where the 8-foot hypotenuse is the lumber, and the "height" of the triangle is 4-feet. It would seem 2 brackets (the kind used in making decks) on each end, screwed into the studs would be suitably strong.

The "Sagulator" (google it!) seems to think that such a setup would only experience a total 0.01in sag in the center of the span.

The heavy bag would just hang from this with a strap that loops over the beam.

An 8-foot span basically means I have a lot of clearance on either side.

I suppose I could just go right into the ceiling joists, but with my proposed setup I can slide the bag to one end or the other and create a bit more of a dynamic setup (albeit it looks a bit more unsightly).

Thoughts or suggestions? Or am I crazy?

I have been researching DIY Latex / Hybrid mattresses lately and have been thinking about pulling the trigger. I've been eying a full latex build, 3 inches of Firm, Medium, and Soft talalay (firm -> soft).I was able to find a good amount of information between Reddit (https://www.reddit.com/r/Mattress/comments/otdqms/diy_mattresses_an_introductory_guide/?rdt=54627) and Arizona Premium Mattresses, but I feel like I'm lacking information about people's anecdotal experiences.

Have you gone the DIY route before? Was it a success? Did you end up effectively buying multiple mattresses worth of components trying to dial it in? Looking back would you just buy a bed in a box? Any insight / tips would be very much appreciated.

I'm looking into insulating the attic above a closed-in back porch & the estimate also included adding additional insulation on top of the blown-in in the attic.

What kinds of factors can be used to think about the value of additional insulation?

For reference, I'm in Florida & keep setpoint around 80 degrees F most of the time when home, and 86 when not home. Power bills in the summer are in the $150-$180 USD range.

It's currently R27 and the quote is to add R11 to bring it up to R38. Code here appears to put new construction at R38 as a minimum, but looking at some charts - it looks like I might have already hit diminishing returns?

This chart I found on "Energy Vanguard" seems to suggest that going from 27 to 38 isn't much of a difference.

Does anyone else have any insight on when those diminishing returns are hit, and if it can make any appreciable difference in power bills? The house itself is comfortable enough, without large swings in temperature.

Growing up we had a carpet washer we would use once a year or so, but we had a dog and 3 messy kids.

Now that I'm grown up, I'm wondering if people regularly wash their carpets. I know you can rent some powerful units from local stores or get a portable one yourself, but Im actually wondering how common this is for people to do somewhat regularly (vs doing it when necessary due to pet accidents)